Cisco 1000
The Cisco 1000 Series were low end branch office routers. Available in fixed configurations supporting 10baseT ethernet, ISDN and serial interfaces. These routers are no longer supported and are replaced by the Cisco 800 Series routers. The launch date was 1995 with the End of Life (EOL) date being 2003, and end of support concluding November 2006.
Models available
Cisco models
- 1001 - 1 Ethernet (10baseT)(RJ45), 1 Serial (V.35) (Leased Line LAN Extender)
- 1002 - 1 Ethernet (10baseT)(RJ45), 1 Serial (X21) (Leased Line LAN Extender)
- 1003 - 1 Ethernet (10baseT)(RJ45), 1 BRI ISDN S/T Interface
- 1004 - 1 Ethernet (10baseT)(RJ45), 1 BRI ISDN Integrated NT1
- 1005 - 1 Ethernet (10baseT)(RJ45), 1 Async#/Sync (network) Serial (DB60)
- 1020 - 1 Ethernet (10baseT)(RJ45), 2 (Max) Async Serial (Dial on Demand Asyncronous Router)
(#)Running serial port in Async mode requires an IOS image that supports it such as c1005-qy-mz.xxx.bin (IP/ASYNC) or c1005-nqy-mz.xxx.bin (IP/IPX/ASYNC)
CiscoPro models
These models were offered in the late 90's, with virtualy identical hardware to the Cisco vairiants (however with a white paint job). These routers were priced aggressively and were restricted to 'crippled' IOS featuresets. The final CiscoPro IOS was 11.2, and some routers were able to be upgraded to compatible full IOS images.
- CPA1003-A CPA 1003 - Ethernet/ISDN BRI router with IP, bridging software
- CPA1003-C CPA 1003 - Ethernet/ISDN BRI router with IP, AT software
- CPA1003-D CPA 1003 - Ethernet/ISDN BRI router with IP, IPX software
- CPA1004-A CPA 1004 - Ethernet/ISDN BRI with NT1 router with IP, bridging software
- CPA1004-C CPA 1004 - Ethernet/ISDN BRI with NT1 router with IP, AT software
- CPA1004-D CPA 1004 - Ethernet/ISDN BRI with NT1 router with IP, IPX software
- CPA1005-A CPA 1005 - Ethernet/serial router with IP, bridging software and X.25
- CPA1005-C CPA 1005 - Ethernet/serial router with IP, AT software
- CPA1005-D CPA 1005 - Ethernet/serial router with IP, IPX software
Specifications
- WAN Speed (ISDN/Modem/Dual Modems/Serial): 128kbps / 28.8kbps / 57.6 kbps / 2 Mbps.
- LAN Speed: 10Mbps.
- Protocol support: IP, IPX, AppleTalk and transparent bridging.
- Software features: PPP, Compression, Dial-on-Demand routing, SNMP
- Routing protocols: RIP, Enhanced IGRP, GRE, IPX-RIP, (AppleTalk) RTMP
- Software options: Cisco ConfigMaker (tool for configuring a network of routers), CiscoWorks Windows (centralized management)
- CPU: Motorola 68360 (25 MHz)
- RAM: 4 - 16MB (One memory slot is available that is compatible with 4, 8 or 16 MB 72pin SIMM modules)
- Flash: 2 - 4MB (All models used a PCMCIA (Type 2) card for flash storage (2 or 4 MB flash cards are supported)
- Boot PROM: 1 MB
- NVRAM: 8 KB
- Power supply: 12VDC external power supply
- Dimensions: 4.4 x 20.3 x 21.1 cm
1001 / 1002 models
The LAN Extender connects to a central 'host' router. The host router provides routing services to the LAN Extender, and all configuration is done remotly from the central router. The host router is connected to the 1001 via a leased line connection (up to T1/E1). The lan extender could be run with Cisco 7000 series, Cisco 4000 series, Cisco 2500 series, and AGS+ host routers. Host routers had to be running IOS Release 10.2 or later[1]
1020 model
Developed through an alliance with Livingston Enterprises. Features two WAN ports, one asynchronous port supports PCMCIA modems up to V.34 rates (28.8 Kbps) and an external modem can be connected to a second asynchronous/console port to achieve aggregate throughput of up to 57.6 kbit/s uncompressed.
References
Links